Service area · Tempe, Arizona
Concrete cutting in Tempe.
Core drilling, wall sawing, slab sawing, and green cutting in Tempe from Concrete Coring Company, the Phoenix crew that has been cutting the Valley since 1961.
Core drilling · Tempe
Eight-inch cores in the seating bowl.
Eight-inch cores, ten inches deep, straight down through the seating deck at the Angels’ spring training ballpark in Tempe. The rig sets up between the rows, the vacuum runs the whole time, and the core comes out in one clean plug you can stand on the step and look at.
Ballpark work is all about the calendar. You get the stadium when the team does not, the cut has to be clean because everything around it is finished, and it has to be picked up and gone before the gates open again. Tempe is fifteen minutes from our yard, which is usually why we get the call.
- Core Drilling: up to 64″ diameter. Whatever the special request, we have the resources to accommodate it.
- GPR Scanning: we find the rebar, conduit and post-tension cable before the bit goes in.
- Wet cut, slurry vacuumed as we go, and the deck left the way we found it.
Core drilling · Tempe
Down the steps, out to the infield.
The same job from the top of the section — the core sitting on the step where it came out, the seats back in place, and the field beyond. Nothing left behind but the hole we were asked for.
Core drilling · Tempe
Cores at a Central Arizona Project checkpoint.
The Central Arizona Project does not hand its work to just anybody. The contractors on that list are picked, and when one of them needs a hole cut, they call us. This is a checkpoint in Tempe. We have twenty-eight of these checkpoints on the books.
Inside it is a live room — power gear on one wall, fire alarm panel on the other, none of it something you switch off for the afternoon. So the containment goes up before the bit turns, the rig runs horizontal off its own anchor, and the water is caught at the hole instead of running across a floor full of equipment. Then look at the edge of the core: round, clean, and nothing left to patch.
- Core Drilling: through block and stucco in occupied plant rooms, both faces clean.
- Containment and slurry capture set before drilling, around live electrical and alarm gear.
- Twenty-eight checkpoints on the books — same crew every time, so the site already knows us.
Core drilling · Tempe
Containment up before the bit turns.
The rig anchored and running horizontally in a live room, plastic taped off around the work and the water caught at the hole. Cutting concrete next to energized gear is mostly about what you do before you start.
Core drilling · Tempe
One clean core at a semi-truck plant.
Sick of the mess? Forget the rest and call us. One core, straight through the wall of a working semi-truck plant in Tempe, and nobody inside had to clean up after us.
The plastic went up inside first: sheeting over the wall, taped tight around the mark, so the water and slurry stayed on our side of it and off the plant floor. The rig anchored on the outside and the core went through right where it was marked. One round hole, and a plant that never had to stop working around us.
- Core Drilling: through the wall of an occupied plant, rig anchored outside.
- Plastic and tape up inside before the bit turned, sealed around the mark.
- One hole is still a job. Same setup whether it is one core or forty.
ASU, the Mill Avenue corridor, the Broadway and Priest industrial strips, and the Loop 101 tech buildings. Tempe is fifteen minutes from our yard.
Same men, same equipment, same 24/7 number as every other job we do. Asphalt, block, and concrete, we cut it all, and we have been doing it in Arizona since 1961 under license ROC071382.
What we do in Tempe
Most Tempe jobs start as core drilling in Tempe and grow from there, so we bring the whole list — wall sawing, slab sawing, green cutting, grinding, GPR scanning and demolition — off the same trucks, with one number to call.
- Core Drilling: Holes through anything, up to 64″ diameter. Whatever the special request, we have the resources to accommodate it.
- Wall Sawing: Door, window, HVAC and structural openings cut clean through concrete and block.
- Slab Sawing: Floors, roads, and lots. We regularly take the jobs other slab sawing companies can’t.
- Green Sawing: Control joints cut the day of the pour with Soff-Cut saws. Zero risk of losing the slab.
- Concrete Grinding: High spots, trip hazards, and rough edges ground smooth.
- GPR Scanning: Ground-penetrating radar finds the rebar, conduit, and cables before the blade does.
- Demolition: Cut it, break it, haul it. Selective concrete removal without the collateral damage.
Why Tempe contractors call us
- Open 24/7. Nights, weekends, and the 5am start that keeps your schedule on track.
- No job is too big or too small. We have drilled up to 64″ diameter, and whatever the special request, we have the resources to accommodate it.
- Our men are trained to work safe and leave the job clean.
- Blades made special for us, because Valley river rock eats ordinary diamonds.
Tell dispatch the address in Tempe, what needs cutting, and when. You’ll get a straight answer and a truck.
“Had these guys come out to a job in Tempe and they did an EXCEPTIONAL job! In and out! Keep area clean and were very professional. Will definitely use them for our coring needs in future!”
★★★★★ matthew bowman — review left on Google
Tempe questions we get
Can you work around a campus or an occupied building in Tempe?
Yes. Tempe work is often in buildings that never really close, so most of it happens at night or on a weekend. We cut wet, capture the slurry, protect the finishes and leave the space usable.
Is access a problem in downtown Tempe?
Rarely, and that is by design. Where a truck cannot reach or a rig will not fit, we bring electric and hand equipment in and, when the job calls for it, we fabricate the bracket to hold it.
Do you scan slabs before cutting near Mill Avenue?
Yes. GPR scanning locates rebar, conduit and post-tension cable before the blade or bit touches concrete, and we mark the clear zones on site.
Do you cut asphalt as well as concrete?
Yes. Asphalt, block and concrete, we cut it all -- lots, drives, trenches and roadway.
How far is Tempe from your shop?
About fifteen minutes of Valley freeway from our Peoria yard, and our trucks are already all over the east Valley daily. Call 602-268-1439.
Asphalt, block, and concrete. We cut it all.
For your job, we will go anywhere. One number, answered 24/7, and a crew that has been cutting Arizona since 1961.
Call 602-268-1439